xavier_roch Posted January 29, 2010 Share Posted January 29, 2010 <p>I, too, want to thank you for your work. After 1 failed attempt due to some confusion reading the almost too much help extra information and comments, I got my new Coolscan 5000ED to load and run with Nikon Scan 4.0.3 under Windows 7 64-bit Ultimate without a single hiccup thus far.<br>My initial confusion and failure was caused by seeing so much discussion about using VueScan drivers when none are needed at all - except for your modified scanners.inf file which you say came from the VueScan install. I also did not yet see unilt later the additional addiitonal changes to the scanner.inf regarding the LS-5000 for 64-bit.<br>Since I used Acronis Try Mode, I was able to reset my CPU back to before the 1st attempt. For those who also might be confused by all the many comments, here is what I did for my Coolscan 5000 with Nikon 4.0.3 under Windows 7 64-bit.</p><ol><li>Turned off scanner.</li><li>Did complete normal install of Nikon Scan 4.0.03</li><li>Reboot computer.</li><li>Created folder "C:\Program Files (x86)\Common Files\Nikon\Driver\ScanFudge". The folder location is not important but my location nicely sits next to the two standard driver folders already there.</li><li>Copied and saved Steel's fantastic "scanners.inf" file to that folder.</li><li>Edited Steel's INF file to copy the "LS-5000" line in [Models] section to the [Models.ntamd64] section for 64-bit operation.</li><li>Copied the Nikon driver file (NKScnUSD.dll) from the adjacent ScanUSB folder. There is also an identical copy of the same driver file in the Scan1394. I verified that with a boinary compare so it doesn't matter which one you copy.</li><li>Turned on scanner.</li><li>Windows 7 complained about not finding a driver. Canceled that error dialog.</li><li>Opened Device Manager</li><li>Right clicked the LS-5000 devices now shown as uninstalled under devices.</li><li>Requested to browse for driver.</li><li>Pointed to my new folder.</li><li>Voila! Windows happily installed the new driver.</li><li>Started Nikon Scan and away I wernt. Now very happy!</li></ol><p>Thanks, Steel. I am a happy camper.</p><p>I then moidified the scanners.inf file, as several explained, to coadd the LS-, everything,</p> Link to comment Share on other sites More sharing options...
xavier_roch Posted January 30, 2010 Share Posted January 30, 2010 <ol> <li>Ignore the last line of my last response. It was edit garbage.</li> <li>Steel? I noticed several other beneficial addendums to your famous scanners.inf customization that add 64bit support of some scanners that were not already in the 64bit section (and 1394?). I think it would be very beneficial to the world if you or someone else who is more familiar with the details than I am if they could update scanners.inf to include all those changes noted in this forum thus far so it works with all Nikon scanners. I am a newbie here and only have the 5000ED under Windows 7x64 via USB. Since Nikon is not producing any new models, it would be a logical and final step to take.</li> <li>Thanks again to you and everyone else here. After happily and madly testing my 5000ED under Windows 7 for 2 days of near-continuous use, it has not hiccupped once (knock on wood) and the scans are beyond epectations!</li> <li>Ps. I am finding that the 5000-ED is quiet LOUD (like an MRI machine) when doing an initial (or redraw) preview scan. But, both pleasantly and unexpectedly, it is VERY quiet and FAST doing a final 16x multi-sample 4k dpi scan! Just a few minutes! I wondered if others found that. </li> </ol> Link to comment Share on other sites More sharing options...
ron_mcelvain Posted February 3, 2010 Share Posted February 3, 2010 <p>I just wanted to add my appreciation for this contribution by <a href="/photodb/user?user_id=4781943">Steel Chn</a>. Thanks to him and the others participating in this dialogue, my Nikon Coolscan IV ED/Nikon Scan 4 is working with my Windows 7 64 bit OS. I can't understand Nikon's seeming lack of support in this area, but am grateful to users/forums like this that allow me to continue using "legacy" hardware!</p> Link to comment Share on other sites More sharing options...
cristian_baitg Posted February 5, 2010 Share Posted February 5, 2010 <p>I also would like to add my big thank you. Worked perfect on my win 7 64 bits. It's really weird that Nikon is not able to support their users that bough their expensive equipment. Thanks again</p> <p>Cristian B</p> Link to comment Share on other sites More sharing options...
ed_lange Posted February 22, 2010 Share Posted February 22, 2010 <p>@ Xavier Roch:<br> this way (step 1 to 4 incl. the modified steel-driver) works too for Windows 7 professional x64 AND the <strong>feeder unit SF-210</strong> ! There is still some problem at the startup (nikonscan doesn't always recognize the LS 5000 with the SF-210). I simply took out the SF-210, inserted it again. After this it worked.<br> It remains some problem with scanner plus unit after switching the scanner off. But after a restart of nicoscan / and or the scanner it works again.<br> Not 100 perfect but better than having a complete Windows XP on a virtual machine just because of one single scanner.</p> Link to comment Share on other sites More sharing options...
embar__go Posted March 16, 2010 Share Posted March 16, 2010 <p>Hi,</p> <p>here is my small contribution, first of all thanks for this job, it allows me to make my CoolScan (LS 50) work with Win7 64b. Just one point, I had to follow <a href="../photodb/user?user_id=5346921">William LaPree</a> advice:</p> <p><em><strong>hey i just registered to let you know that if you copy the line from<br /> [Models]<br /> "Nikon LS-50" = USBScanner,USB\Vid_04b0&Pid_4001<br /> down to <br /> [Models.ntamd64]<br /> "Nikon LS-50" = USBScanner,USB\Vid_04b0&Pid_4001 </strong> </em><br> <em><strong>it will make the coolscan V ED work in windows 7 RTM 64 bit. i assume that any of the scanners listed in the [Models] moved down to [Models.ntamd64] will enable them to work in either vista x64 or windows 7 x64 (the USB ones anyhow). this is a huge win for me as i was fearing i was going to have to setup xp mode and jump through hoops to get it working!</strong> </em></p> <p>Without that modification Windows won't find the file for upgrading the soft, when done then it works fine.</p> <p>THX</p> Link to comment Share on other sites More sharing options...
enzo_franchini Posted March 18, 2010 Share Posted March 18, 2010 <p>Hello Steel<br> wonderful work. No problem between my 9000 and Seven Professional 64 bit.<br> Thank you.</p> Link to comment Share on other sites More sharing options...
steve_wilkes Posted March 29, 2010 Share Posted March 29, 2010 <p>Following your instructions I managed to get Vista x64 and my coolscan 9000 working with no problems.<br> Thank you so much, I can now run my scanner on my high power x64 PC. Nikon surely should have done this customer support with minimal effort to themselves.....</p> Link to comment Share on other sites More sharing options...
michel_cadart Posted April 4, 2010 Share Posted April 4, 2010 <p>Hi,<br> Due to Steel Chn driver, my Coolscan 9000ED worked fine on Windows7 x64 till today.<br> I mean that the last time I used it, 2 months ago, it was fine, and today, without any change to Nikon Scan nor to my driver, I cannot get a scan anymore. When I run Nikon Scan, at first, I get a message : "Please remove the flim holder and click OK to try again". After a few try, reset, on/off on the scan, ... I manage to get my film thumbnails in Nikon Scan, but when I scan it, I get views with only thin black and white stripes and no picture. I searched with Google, I didn't find anything to help me. I downloaded Vuescan and manage to get a scan with it, so it isn't a hardware issue. I uninstalled Nikon Scan and the driver, reboot and installed it again, it didn't fix the problem.<br> Any idea ?<br> Thanks a lot if somebody can help me.</p> Link to comment Share on other sites More sharing options...
andrew_hull Posted April 5, 2010 Share Posted April 5, 2010 <p>Any news on this working for Windows 7?</p> Link to comment Share on other sites More sharing options...
acmelabs Posted April 5, 2010 Share Posted April 5, 2010 <p>Hi,<br> Many people contributing to this thread have these scanners working under Windows 7. But if you mean is Nikon working on a solution, the answer is no, as follows:</p> <p>"Can I use my Nikon Scanner with Windows 7, Leopard, Snow Leopard, or a 64-bit operating system? </p> <p id="rn_solution"><th id="label__14" > </th> <td id="content__14" > </td> The use of Nikon Scan software with Windows 7 (any version), or Mac OS 10.5.x or later, or any 64- bit operating system (including 64-bit, 32-bit or Compatibility mode) is not supported.<br> We suggest trying a third party software option such as Vuescan from Hamrick.com or Silverfast software."</p> <p>materialsguy</p> Link to comment Share on other sites More sharing options...
thomas_janik Posted April 24, 2010 Share Posted April 24, 2010 <p>My thanks to Steel Chn as well. I had some problems with Vista 64, the scanner occasionally would hang. I used a similar scanner.inf file to enable the Minotla 5400 as well<br> I recently installed Windows 7 (64) and both scanners installed using Steel's file. <br> However, I'm curious if anyone has used either scanner in XP mode on 7 using the Nikon and Minolta supplied drivers, seems that it could avoid some of the issues reported above.</p> <p>Tom</p> Link to comment Share on other sites More sharing options...
segedi Posted May 6, 2010 Share Posted May 6, 2010 <p>Got a new 9000 ED and installed the newest version of Nikon Scan on my Windows 7 Ultimate, 64-bit. It seemed to work fine out of the box, but I went ahead and installed the above driver and that works fine too. So far I've only run a half dozen scans, but it works quite well!<br> Thanks Steve for the driver and Alex, I followed your checklist too.<br> I did download the latest version of SilverFast and was impressed that I could pick my film type and it did change the appearance of the scan. But I actually thought the NikonScan did a better job in preserving shadow details. And I'm really not impressed with the Silverfast price tag!<br> Kevin</p> Link to comment Share on other sites More sharing options...
bob_hamilton2 Posted May 11, 2010 Share Posted May 11, 2010 <p>Thanks to all, especially Steel Chn. I got my Coolscan V operating on Win7 Professional 64 bit. There are some key posts to getting it working.<br>First Steel's post of Jan. 2, 2009, followed by his second on Apr. 28, 2009 or Dim K's on Nov. 8, 2009. Lastly and the one for my scanner is Willian LaPree's on Nov. 8, 2009.<br>Thanks again to everyone.</p> Link to comment Share on other sites More sharing options...
joel_albert2 Posted June 5, 2010 Share Posted June 5, 2010 <p>Steel,<br> Let me add my sincere thanks to you for posting this information.<br> Worked like a charm on a Vista 64 bit with a Super Coolscan 9000 ED.<br> Now I can blow away my Alternate Vista-32 bit boot and simplify my workflow significantly.<br> Its a great scanner but I really dislike Nikon's handling of this.</p> <p>Anyway, you have done me a great service and it is much appreciated.</p> <p>Joel</p> Link to comment Share on other sites More sharing options...
ricardo_huaman Posted June 6, 2010 Share Posted June 6, 2010 <p>Hi Steel,<br> I'm trying to get my LS-30 to work on a 32-bit Windows 7 system. I use an Adaptec 2906 card and have tried their XP, Vista and 7 drivers along with different versions of ASPI. Vuescan cannot find my scanner even after loading the drivers as per Hamrick's instructions. However, the scanner does work great in Ubuntu 10.04 with Vuescan, but I'd rather not have to dual boot to use Photoshop. I was wondering if changing the line "%Mfg%=Models,ntamd64" to "%Mfg%=Models,ntamd86" would make your file usable on my system.<br> Thanks,<br> Ricardo</p> Link to comment Share on other sites More sharing options...
ricardo_huaman Posted June 9, 2010 Share Posted June 9, 2010 <p>ntx86?</p> Link to comment Share on other sites More sharing options...
gerald_kaiser Posted June 10, 2010 Share Posted June 10, 2010 <p>Hi Ricardo,<br> I am running VueScan 8.6.34 on W7 32bit (Old drivers option answered with YES) and using my old LS-1000 and LS-2000 as well as the newer LS-5000 without a problem so far. After that was running fine, I tried to install NikonScan, but the 4.03 version I used come up with an error message during the INSTALL-process. Maybe I have to follow Steel Chn's advice given for the x64 version to uninstall VueScan, then install Nikon Scan, then reinstalll VueScan. But that is not an urgent issue to me.<br> Steel, thanks a ton for your fine work to get the LS-4000 and other scanners to work with x64 Vista, makes me feel optimistic to use W 7 x64 (which I throw out to be able to use scanners).<br> Regards,<br> Gerald</p> Link to comment Share on other sites More sharing options...
ricardo_huaman Posted June 10, 2010 Share Posted June 10, 2010 <p>Thanks for the reply, Gerald. I did load the old drivers. I wonder if I need a different SCSI card for Windows 7 or if I should try uninstalling Vuescan (again). I'll keep at it.</p> Link to comment Share on other sites More sharing options...
gerald_kaiser Posted June 11, 2010 Share Posted June 11, 2010 <p>Hi Ricardo,<br> sorry, being a first time replier I had to register first and after all that jazz I forgot to write half of my intended reply. I have tried the Adaptec SCSI-cards 2940/2940W, 2940U/2940UW (32bit-driver aic78xx_aic78u2_win7_2k8r2_x86_v605457.exe) and 29160N (32bit driver u160_w7_ws08r2_x86_drv_b7_5_645_100.exe) all with their W7 drivers from the Adaptec page (downloaded the driver a few days back). Their used to be an Adaptec 2904 and an 2940S6, but for those I could not find a W7 driver. So maybe you should go for a 2940U or 2940W or a newer SCSI card for which you find a driver on the adaptec website.<br> With VueScan you also do not need the ASPI drivers like you do for NikonScan, quite important, since Adaptec does not supply ASPI drivers for Vista or Windows 7 anymore.<br> Hope that helps a bit.<br> Regards,<br> Gerald</p> Link to comment Share on other sites More sharing options...
ricardo_huaman Posted June 11, 2010 Share Posted June 11, 2010 <p>Hi Gerald,<br> I tried both the Adaptec W7 and Vista drivers before but without any luck. However, I hadn't realized that not only did I need to unzip the files, but that I manually had to go to Device Manager and point the SCSI controller in the right direction. When I did that the drivers were installed and I got a pop-up message saying that my LS-30 was installed and ready to go. I just made my first scan in Windows with Vuescan. Now I need to work on getting Nikon Scan 3.1.2 up and running on Windows 7.<br> Thanks!<br> Ricardo</p> Link to comment Share on other sites More sharing options...
gerald_kaiser Posted June 19, 2010 Share Posted June 19, 2010 <p>Hi Ricardo,<br> I did some looking about for ASPI drivers. Some people wrote that the Adaptec ASPI driver V4-7-2-a2 should work on Vista and W7. Someone mentioned a ForceASPI for his CD-ROM device and some sound-software, but I have not looked into it. Should you get the LS-30 to work with NikonScan then please tell us on this thread as well, would be interesting to others and to LS-2000 (maybe even LS-1000) users.<br> Regards,<br> Gerald</p> Link to comment Share on other sites More sharing options...
chris_a3 Posted September 6, 2010 Share Posted September 6, 2010 <p>Just like to add my grateful thanks to Steel Chn and Shaun Merrigan. My 5000-ED (LS-5000) now works fine under Windows 7 Ultimate x64. Much appreciated, guys.</p> Link to comment Share on other sites More sharing options...
brad_herman1 Posted October 21, 2010 Share Posted October 21, 2010 <p>What about Windows 7 Ultimate 32-bit and Nikon Scan 4.0.x? Will it work the same way? Will the standard Vista install of Nikon Scan 4.0.3 work?<br> Thanks<br> Brad</p> Link to comment Share on other sites More sharing options...
gerald_kaiser Posted October 23, 2010 Share Posted October 23, 2010 <p>Hi Brad,<br> the NikonScan 4.0.3 will install on Windows 7 Ultimate and work OK, at least it does with me. Do not forget to first uninstall any other Nikon-Scan versions you might have installed on a testbasis, otherwise you get an install-time-error (on the Nikon website and on some Nikon-CDs you find the uninstall-pgms for the related NikonScan version). <br> Good luck,<br> Gerald</p> Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now