Tony Rowlett Posted January 4, 2000 Share Posted January 4, 2000 It's easy for me to control the temperature of water coming out of the faucet when the water is coming out at normal rates, i.e. rates that would seem to be too much for the small Minox daylight tank. When I diminish the water flow to the recommended thin stream, I find it almost impossible to control temperature, even a little bit. Not a huge problem with films like Tri-X, but I am more concerned with Tmax 100, the film I'm currently using.<p>Questions:<p><ul><li>Is film adequately washed with a much higher rate of flow from the faucet when using the daylight tank? Does it go inside properly or is it just pushed over the top?<li>With a lower, thin-stream flow, how do you control temperature to at least keep it in the ballpark of 65-70F ?</ul> Backups? We don’t need no stinking ba #.’ _ , J Link to comment Share on other sites More sharing options...
michael_goldfarb1 Posted January 5, 2000 Share Posted January 5, 2000 A dissenting view: I know this is heresy, but I only use the Minox Tank for development proper. <p> When my timer goes off, I turn off the lights, pull out the Tank spiral with the film still on it (I use my right thumb to keep the cassette on its little mount), dunk it into a large graduate of water (roughly the right temperature, to prevent reticulation) two or three times, then unspool the film and drop it into a tray of fixer. After about a minute, I turn on the lights and swish the film around in the fixer tray until it's clear (taking care not to scratch the emulsion side), then leave it in the fixer for a couple of additional minutes. <p> I then wash the film in a small tray with a faucet running into it (again at roughly the right temperature to prevent reticulation), swirling the film from the cassette end and taking care not to bruise the emulsion side. Most films only need about three minutes of this, but TMX takes roughly twice as long to finally lose its purplish cast. Then a quick dunk in a dilute PhotoFlo solution, and hang it up. <p> I've done this with nearly a hundred rolls over the years - the Minox Tank is THE solution for developing, but for rinsing, fixing, and washing, I find not using it works fine... and I NEVER worry about adequate solutions at each stage, as I'm using vast amounts of them compared to the size of the film. Link to comment Share on other sites More sharing options...
labce__ Posted January 9, 2000 Share Posted January 9, 2000 I use the Minox tank for developing and fixing,then unwind the film into a larger 35mm tank for rinsing.I place it in the sink with running water flowing through the tank for an hour(probably too long) and it comes out perfect. Link to comment Share on other sites More sharing options...
MTC Photography Posted January 14, 2019 Share Posted January 14, 2019 I use Minox tank to develop Minox film. Use the Minox termometer to monitor the temperature. After that fixing, in the Minox tank. finally put the Minox tank under runnig faucet to wash the film for 30 minutes Link to comment Share on other sites More sharing options...
B. C. S. Posted January 14, 2019 Share Posted January 14, 2019 I'm sure the higher flow will still give you good washing. Sure, more is going over the edge, but the turbulence will be greater and should get down to the bottom. Personally, unless I want to develop in the field (can't remember the last time I did that), I use stainless reels and tanks. I know you have to load in the dark, but the minor size reels are very easy to load. Then I can treat just like 35mm or 120 film. Just my way. 1 Link to comment Share on other sites More sharing options...
Jochen_S Posted January 15, 2019 Share Posted January 15, 2019 I'd either hang something like a solar shower bag (full of enough water at hopefully right temperature - tap too hot, it'll get there) over my bathtub and drain the needed rinsing water from there or change water multiple times instead of keeping it flowing. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now