leon chang Posted November 7, 2006 Share Posted November 7, 2006 I made a rather stupid mistake whilst loading a roll of Provia 400F and later 1 roll of Kodak Tri-x. The iso- dial on my camera was still set to "200" whereas these films are both 400- speed. Can this be corrected by the lab and if so, what instructions do I have to give them? For the record I just continued to shoot on iso 200.. Link to comment Share on other sites More sharing options...
Jochen_S Posted November 7, 2006 Share Posted November 7, 2006 i wouldn't worry too much about the Tri-X. besides it's ability to cope with the overexposure a developer like Perceptol might be a reasonable way out. There are plenty of fine grain developers which cost 1 f-stop. I fear the worst for the Provia. Link to comment Share on other sites More sharing options...
William Kahn Posted November 7, 2006 Share Posted November 7, 2006 I agree with Jochen. Tri-X especially has more than two stops latitude for overexposure, and you're only one stop over. I think the Provia will be OK, too, but you're a lot closer to the latitude limit there.... Link to comment Share on other sites More sharing options...
leon chang Posted November 7, 2006 Author Share Posted November 7, 2006 Thanks! So what do I instruct to my lab? Link to comment Share on other sites More sharing options...
steve_levine Posted November 7, 2006 Share Posted November 7, 2006 Unless the Provia contained a non-repeatable event or subject, I would re-shoot. If it is real important, shoot a test roll at the same ISO and have the lab try to shorten (pull) the processing(developer) time. You can then scan it, and save it. Whereas if you over expose chrome film a full stop, you might get back blank film if the subject has a lot of light areas. Link to comment Share on other sites More sharing options...
m_. Posted November 7, 2006 Share Posted November 7, 2006 >>So what do I instruct to my lab? instruct them to develop the tri-x normally and provia pulled 1 stop. Link to comment Share on other sites More sharing options...
frank.schifano Posted November 7, 2006 Share Posted November 7, 2006 Provia, being a color transparency film, has very low tolerance for exposure errors. You might try asking the lab to do a 1 stop pull, but I would not expect too much from this technique. A cursory look through Fuji's tech sheet for the product (available here: http://www.fujifilmusa.com/JSP/fuji/epartners/bin/PROVIA400FAF3-066E_1.pdf) mentions nothing about push or pull processing for this film. Assuming that you do your own B&W processing, the overexposed Tri-X will present no problem. Developed normally in something like D-76, you'll get negatives that are a bit dense but still capable of producing decent images. Full strength Microdol-X or Perceptol will cost you about 1 stop of film speed, putting the film right on target for one of these "fine grain" developers. Many years ago, Tri-X in Microdol-X was a standard combination for me, and one that delivered pretty good results. Over time, my tastes changed and so did Tri-X. Modern Tri-X is a much finer grained and better all around film than it once was, and the need for something like Microdol-X has largely disappeared. Link to comment Share on other sites More sharing options...
drjedsmith Posted November 10, 2006 Share Posted November 10, 2006 Uh...the new Provia 400 is the MOST pullable/pushable slide film available. It should easily tolerate this, a one stop error. I agree with "M" and that post:<BR>Instruct your lab to pull the provia 1 stop.<BR><BR>For the Tri-X, it is very forgiving, and you could probably just cut your developing time by about 1 to 2 minutes or so, if using D76 or XTOL.<BR>Jed Link to comment Share on other sites More sharing options...
bill_tuthill Posted November 10, 2006 Share Posted November 10, 2006 Jedidiah is right -- there are several photo.netters who find Provia 400F better pulled one stop than as-rated. Pulling reduces contrast, which is too high in this film. You might find yourself making this "mistake" again! Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now