aa Posted November 27, 2005 Share Posted November 27, 2005 I just developed the last 2 rolls of a 12 roll project shooting Ilford PanF+ at ASA 32 and developing in 1:100 Rodinal, and encountered a fogging and "splotches" problem on just these last two rolls. See here for an example: http://blackaawhite.blogspot.com/ http://photos1.blogger.com/blogger/7987/228/1600/40221b.jpg http://photos1.blogger.com/blogger/7987/228/1600/40221.jpg Notes: The temp is always 20-22C and I adjust the time accordingly. (from 13.5 minutes for 20C) I have used the same stop and fix (Kodak) throughout...I wouldn't think this was the problem since the last two rolls developed were fine,although I probably don't change these solutions enough. I do not re-use the Rodinal. The ambient temperature of my darkroom(bathroom) has dropped a few C's, so maybe the Rodinal precipitated (I thought Rodinal was always this way though). I seem to remember usually shaking the 125mL Rodinal bottle vigourously before use, and don't recall doing that when the problem occurred. The film is loaded in complete darkness, the stop and fix are added in almost darkness. I use a plastic 2 roll Patterson developer. Both rolls were at below freezing levels in strong wind and right near the ocean. I can't think of anything and would hope that someone with a lot of experience can look at film and know what happened. Thank you, Andrew Albright<div></div> Link to comment Share on other sites More sharing options...
aa Posted November 27, 2005 Author Share Posted November 27, 2005 The full picture demonstrates the problem better.<div></div> Link to comment Share on other sites More sharing options...
michael_gudzinowicz1 Posted November 27, 2005 Share Posted November 27, 2005 Try refixing the film with fresh fixer. Link to comment Share on other sites More sharing options...
jon_porter1 Posted November 27, 2005 Share Posted November 27, 2005 I agree with Michael. It looks like your fixer was exhausted. I use Ilford Rapid Fix one-shot for 4-5 minutes, giving four inversions every 30 seconds. Link to comment Share on other sites More sharing options...
lex_jenkins Posted November 27, 2005 Share Posted November 27, 2005 If the temperature during shooting was at or below freezing there's a chance that static electricity could have produced those smaller marks when advancing or rewinding the film. Wind on a cold day could make matters worse. So could the use of a motor drive or rapidly winding the film. Link to comment Share on other sites More sharing options...
melvin_bramley Posted November 28, 2005 Share Posted November 28, 2005 Try refixing but I don't think thats your problem.It looks like bad agitation or air bubbles in the developer.The full frame photo looks underdeveloped in the middle compared the the top & bottom. Link to comment Share on other sites More sharing options...
chris_waller Posted November 28, 2005 Share Posted November 28, 2005 Like Melvin, I would suggest that air-bubbles on the film are the problem. Try a pre-soak or more vigorous tapping of the tank when the developer is poured in to dislodge the bubbles. Link to comment Share on other sites More sharing options...
keith_kreeger Posted November 30, 2005 Share Posted November 30, 2005 My vote is static electricity also. The dots are uniform and of positive density, like static would generate. I've seen it before on film left in the camera for some time. Was this roll film (120) or 35mm? Link to comment Share on other sites More sharing options...
aa Posted December 1, 2005 Author Share Posted December 1, 2005 The refixers win the prize! I refixed for 40 minutes with my (obviously) spent developer. This cleared up the problems on the images (but the film is still slightly fogged overall). I'm awaiting a B&H order with some new Ilford one-shot fixer (thanks for that heads up). I think the static electricity was a good suggestion, but kind of hard to tell from the one frame I posted. In photo class, the instructor showed us some examples of static electricity problems and it looked a bit different. (Plus I am careful now to rewind film slowly and while it was cold, the humidity is probably pretty high right on the ocean?) Thanks again everyone, this board saved the day. (I printed one of the pictures tonight and it is my most favorite picture in quite some time!) Andrew Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now