Jump to content

michael_frangos

Members
 View Profile  See their activity

  • Posts

    351

  • Joined

  • Last visited

  • Days Won

    2

 Content Type 

Everything posted by michael_frangos

  1. michael_frangos
    Hasselblad 503CW, C Planar 80/2.8, Rollei RPX 100, Studional (1+30), yellow filter
  2. michael_frangos
    Revealed... Mamiya 645 Pro, FP4+ in Rodinal
  3. michael_frangos
    Thanks for this, Gerber!
  4. michael_frangos
    Thanks, Alan!
  5. michael_frangos
    Hi I was given this anti-static gun recently and wonder if anyone could help me with some instructions of use. Many thanks in advance! regards Michael
  6. michael_frangos
    Olympus OM-4, Zuiko 65-200/4, HP5+ in Studional
  7. michael_frangos
    Mamiya 645 Pro, Sekor-C 45/2.8 N, Ilford Delta 100, Studional (1+15), 6 min.
  8. michael_frangos
    Hasselblad 503CW, CF Distagon 50/4 T* FLE, Rollei RPX400 @ 640, Studional (1+15), 6:20 min
  9. michael_frangos
    This doesn't make sense
  10. michael_frangos
    Kelly Maybe this will help: It's VERY important to mark the position of the lens before you unscrew it. Good luck! Michael
  11. michael_frangos
    Mamiya 645 Pro, Ilford Delta 400, Studional (1+15)
  12. michael_frangos
    Regrettably, not.
  13. michael_frangos
    I have tried to clean the teeth (lol) and “straighten” a couple that had a bent tip Then I put the counter back on the camera and tighten the screw that keeps it in place as much as I could. I’ve run a test-film through. If done carefully, the film advances properly. But I’m keeping an eye out for a donor camera.
  14. michael_frangos
    Hi I have just bought this camera and after developing the first film, I noticed uneven spacing between frames. I pulled out the counter and discovered that unfortunately it is damaged. Does anyone know where I can find a replacement (preferably in EU)? Regards Michael
  15. michael_frangos
    Thank you both for your help! The lens seems to be fine again.
  16. michael_frangos
    It's in place now, I have adjusted focus and tomorrow the camera will be put to the acid test of actual photography. It was easy to screw the tube in, it's embarrassing that I couldn't figure it out from the start. I tried to screw it pressing from above (it wouldn't move), when pinching(?) it from one side and driving it in was what it needed. Finally, I tightened it with that rubber tool. John, I wouldn't trust myself filing slots as you suggested. The thread is so fine I would be afraid to mess it up.
  17. michael_frangos
    Thanks, rodeo_joe! You were right. That retaining ring could be tightened properly in place...with a rubber tool (vacuum pad? from Japan Hobby Tool)
  18. michael_frangos
    Hi I have bought a Bessa I in very good condition, but the lens has a problem. The rear element is loose in its ring (the distance between the glass and the ring is abt 1mm) resulting in out of focus images. Does anyone know how it was held in place? A rubber or metal ring perhaps? Any advice would be appreciated. Regards Michael
  19. michael_frangos
    Burial mound, Sealand, DK Olympus 35 RC (42/2.8), Agfa APX100, Studional (1+15), 4.15 min
  20. michael_frangos
    Hi Eugen Unfortunately, I have sold my projector and deleted the documents, but you may find relevant information at: - Rolleivision legendäre Rollei Zeiss Leitz Dia-Projektoren & ServiceRolleivision 66 / AV - Rollei Legenden . . . Best Michael
  21. michael_frangos
    I have sent you a pm
  22. michael_frangos
    I just used water on my K4M, applied with a piece of cloth and let it stay a bit. The old glue was removed without resistance.
  23. michael_frangos
    Verdun, France Olympus OM-2n, slide film
  24. michael_frangos
    Horizon 202, Ilford HP5+ @ 1600 in Studional (1+15)
  25. michael_frangos
    Seagull 203 (75/3.5), Fomapan 200 in Studional (1+15)
×
×
  • Create New...