rick_strome Posted April 27, 2003 Share Posted April 27, 2003 I have a Hasselblad 500C with a 80 mm lens. I also have a Vivitar 285 flash. Recently I have been experiencing random flash failure (fails to flash about 10% of the time). Does anyone know if it can be determined what component is causing the problem? Is it a bad cord pc connector to the flash. Is it a bad cord pc cord connector to the lens. Is the lens pc cord connector bad. Is the flash pc cord connector bad. Can you do a simple continunity check to determine what item is bad? I do not want to buy a new flash if the cord is bad and vice versa. Thanks for any advice on the above, Rick Link to comment Share on other sites More sharing options...
alex_ragen Posted April 27, 2003 Share Posted April 27, 2003 Rick--I would experiment by trying to recreate the problem with different cords and different lenses, and so narrow in on the malfunctioning component.--Alex Link to comment Share on other sites More sharing options...
LenMarriott Posted April 27, 2003 Share Posted April 27, 2003 Rick, PC cords are the weak link in the chain & if you're lucky a new one will solve your problem. (they lose their tension & become loose fitting or develop intermittent open circuits in the wiring) Sometimes all that is needed is to burnish the PC contact on the end of the cord & on the camera (special but inexpensive tool req'd). Alex's trouble shooting proceedure is right on & will help to isolate the problem. Good luck. LM. Link to comment Share on other sites More sharing options...
al_kaplan1 Posted April 27, 2003 Share Posted April 27, 2003 I'd say the cord. I always carry a few spares! A bit of WD-40 sprayed into the cords PC tip might help if it's a corrosion problem. Let it sit for a few minutes and then rub the inside with a tooth pick, and if you have any, a bit of steel wool. In reality it's usually cheaper to just buy a new cord. Every time the flash misfires you waste film! Unfortunately hot shoe flashes have created a generation of photographers who spent years not using cords. Used to be that we learned early on that cords were cheap and expendable! Link to comment Share on other sites More sharing options...
hasselblad technician Posted April 27, 2003 Share Posted April 27, 2003 Rick, The problem could be the flash unit itself, the cord, or a worn flash terminal on the lens. Do you have another lens that you can try it with? If so, and the flash doesn't misfire on the other lens, it's probably due to a worn flash terminal on the 80mm. If the flash misfires on another lens, then it could be either the flash unit or the cord. Dave Odess Factory trained Hasselblad technician 28 South Main Street #104 Randolph, MA 02368 (781) 963-1166 Link to comment Share on other sites More sharing options...
ptucci Posted April 27, 2003 Share Posted April 27, 2003 I, too, had a 285 that wouldn't fire intermittently. I first suspected the PC cord, because they are "consumables". I switched to 2 others, same problem. Even the red test fire button would have misfires. AHA! its the flash. I unscrewed the shoe mount (2 small phillips head screws), tightened up the electrical connections I could see, and that seemed to take care of the problem. Before I tightened up the connections, a light slap up side it's head would get it firing again. Link to comment Share on other sites More sharing options...
steve_teale Posted April 28, 2003 Share Posted April 28, 2003 Rick, is it a 285 HV (the lower voltage one) or the other one which pushes out a trigger voltage of around 2-300 volts or so ?! With some of the older flashes their trigger voltages could over time wear away any flash contacts. Try with another lens if you can. You can buy safe-sync devices from companies like Wien that keep the trigger voltage down to a safer sub 5 or 6 volts or thereabouts. On the other hand - maybe it IS just the cable ! ;) Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now