jeremy brotherton Posted December 30, 2007 Share Posted December 30, 2007 I just shot a roll of http://www.freestylephoto.biz/sc_prod.p ? 1000002128 RolliOrtho 25 film 36 shots and nothing turned out. The roll was blank other then aflorescent light that registered on the film. I understand that the film is notsensitive to reds and oranges so I used flashes for my lights and I used a greenfilter on my camera maybe I should have used a blue filter? I used my digitalcamera to get an exposure setting then did a equivalent exposure adjustment. Iwent from an ISO of 200 to an ISO of 25 so I went from f8 to 3.5? because it wasthe largest aperture I could get on my camera. I had one flash set to about f16and the other to about f22 and had each light about 2.5 yards from the model. Iset my light meter to ISO 25 and everything but nothing other then the lightshowed up and in only one photo? I heard the shutter open and close. The cameraworks fine so I know it's not that. I think it's just me using Ortho for thefirst type that might be the issue. Any ideas? Link to comment Share on other sites More sharing options...
bob_sunley Posted December 30, 2007 Share Posted December 30, 2007 Sounds like you were way under exposed. f3.5 is a half stop to little, but that should be ok. But what is the filter factor for your green filter. Odds are you cost you a couple of stops as well. I don't quite understand what you mean by setting your flashes to f numbers. What kind of camera and flashes? What shutter speed and was your sync setting set for X for electronic flashes. Link to comment Share on other sites More sharing options...
hitam_jantung Posted December 30, 2007 Share Posted December 30, 2007 Why use a filter? Ortho films are not very sensitive to green (thus the dark foliage), so you effectively cut out most of the useful spectrum. Try it without a filter, rate the film at EI 25, or EI 12 if you're cautious, and use the guide number for your flash to calculate exposure. Link to comment Share on other sites More sharing options...
dave_s Posted December 30, 2007 Share Posted December 30, 2007 I've never used this film, but I suggest the key may be in your green filter. If it was a real full-bore tricolor green, like a #58, it would have a pretty high filter factor, since it absorbs everything except the green wavelengths. You don't say why you were using the filter, but if you don't have a good reason, you might lose it and try again. Another alternative is that you're underdeveloping. Link to comment Share on other sites More sharing options...
frank.schifano Posted December 30, 2007 Share Posted December 30, 2007 Yep, my bet is on the green filter too. Why are you bothering with it in the first place? Link to comment Share on other sites More sharing options...
j. salty Posted December 30, 2007 Share Posted December 30, 2007 I'd say also that you were massively underexposed. The film is rated at ISO 25, but the filter factor of the green is at least 2 stops, so I would metered at around ISO 6. Link to comment Share on other sites More sharing options...
jeremy brotherton Posted December 30, 2007 Author Share Posted December 30, 2007 Ok it was the filter then. I was thinking that since it's a blue green sensitive film the green filter would help make it more contrasty. I didn't think about it filter out colors. I should have used a blue filter it sounds like. Now IR film when you use a red filter it's ISO bumps up I've been told. Is this the same with Ortho film? Link to comment Share on other sites More sharing options...
jeremy brotherton Posted December 30, 2007 Author Share Posted December 30, 2007 I would also like to add that what I mean by saying, "Now IR film when you use a red filter it's ISO bumps up I've been told. Is this the same with Ortho film?" I mean if I use a blue filter on Ortho film will it boost the ISO? I know that sounds weird But I was told by a professor when I was in college that if you use IR film and use a red filter it's ISO rating jumps to a higher rating. Link to comment Share on other sites More sharing options...
j. salty Posted December 30, 2007 Share Posted December 30, 2007 I've never tried Rolli Ortho film, but I have played with a few other brand orthrochromatic sheet films and the ones I've tried are contrasty enough without trying to increase it. Link to comment Share on other sites More sharing options...
photojim Posted December 30, 2007 Share Posted December 30, 2007 If you use IR film and a red filter, the ISO rating doesn't jump higher. Firstly, ISOs are set by specific methods and are standard. Subjective ratings are called Exposure Indexes (or EIs). Even here what your professor said is not quite true. If you use a handheld meter, you would set the meter at a lower ISO than you would metering on the camera through the filter, but this isn't really a change in ISO, it's a change in how you are performing the metering. The film speed doesn't change in either event. Link to comment Share on other sites More sharing options...
dave_s Posted December 30, 2007 Share Posted December 30, 2007 Jeremy, I suggest you don't use any filter, unless you have a good reason to. Depending on what blue filter you choose, you could find yourself with the same problem as with your green filter. One way to look at it is that the ortho film itself acts something like a blue-green filter. It doesn't respond to red wavelengths, so it's like shooting pan film with a 'minus red' filter on your lens, which would be a blue-green 44 or 44A. Link to comment Share on other sites More sharing options...
jeremy brotherton Posted December 30, 2007 Author Share Posted December 30, 2007 I keep looking for a blue green 44 or 44a filter and I can't find one. Any one know why? I type in 44a filter or 44 filter on ebay and nothing? Link to comment Share on other sites More sharing options...
dave_s Posted December 30, 2007 Share Posted December 30, 2007 You don't need a 44/44A with ortho film, if that's your plan. There's no point. To ortho film, these filters would look as colorless as window glass. You could use a 44/44A to simulate an ortho look with pan film. These filters are uncommon and have limited utility, so you might have to do a special order. You might get similar results with a deep cyan CC filter. You could look for a Wratten gel filter. Alternatively, B + W makes (or made) a similar blue-green filter called a 081. OK, don't take this the wrong way-- this project is costing you a few bucks, and what's worse, it is costing you photographic time. I get the idea that you don't have a clear idea how these materials respond to light. Are you sure you have a reason for using them? Link to comment Share on other sites More sharing options...
jeremy brotherton Posted December 30, 2007 Author Share Posted December 30, 2007 Lol No I do understand now. What I'm thinking is if I can mimic the look with pan film and this filter it will cost me less in the long run. Also the film was free, it was a Christmas gift. I thought if I'm going to trying it I might as well ask for it for Christmas so I don't lose money while learning how to use it. Link to comment Share on other sites More sharing options...
cliff coles Posted January 1, 2008 Share Posted January 1, 2008 Hi, I have to put in my two cents worth here. In all the responses, how you processed the ortho hasn't come up. The developer used in processing ortho is very unstable. In fact, there are two solutions that are combined right before you use it and then it 'dies' very quickly, hence mixing right before use. Another developer that can be used is good ole dektol diluted 8 parts water and one part developer. Works very nicely. Why did you shoot ortho in the first place? I hope you got all the answers you need. Signed, an ole ortho user from way back! Link to comment Share on other sites More sharing options...
jeremy brotherton Posted January 2, 2008 Author Share Posted January 2, 2008 O used it to get to know it. Some one said I should start shooting ortho because of my photographic style and interests. But I think I'm going to do either the filter on B&W film or use Efke R25 120 film. Link to comment Share on other sites More sharing options...
profhlynnjones Posted January 15, 2008 Share Posted January 15, 2008 You can convert any panchromatic b/w film with a CC50 or 60 Cyan filter, open up 1 stop, process normally. You can buy such a filter from Harrison & Harrison, Porterville, CA. They are the third generation of creative filter makers. Lynn Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now