william_shepard1 Posted November 7, 1998 Share Posted November 7, 1998 Can the Zone system be used for transparency film? I seem to recall reading that one can use it, but instead of a zone being one stop, make it a half a stop, ie: zone vii would be like zone vi, zone vi would become zone v and a half.(due to the reduced scale of the film vs b&w. <p> Do you all concur with this? Does it apply only to transparency or to color print film as well? <p> Or did I get it mixed up and does it apply to color print and not to transparency? <p> I can't remember where I read it, Adams, or Picker, or some other book on the zone system. <p> I realize that development control is limited, too. <p> Bill Shepard Link to comment Share on other sites More sharing options...
twmeyer Posted November 9, 1998 Share Posted November 9, 1998 i used zone system exposure basics with large format color trans photography for many years and found it extremely useful. <p> be sure to use a spotmeter, and set your own standards using 1/2 zones rather than redesigning the wheel. <p> i found white with detail that was printable to fall about zone 7.5 and black with printable detail around 3.5, but you should find your own reference points. color reproduction on the film varies with lens and films. digital printing has changed the amount of recordable info on film that is reproduceable on paper. <p> developement techniques (push/pull developement) works to a much smaller degree with color films due to shifts in color created by changes in developement time. Link to comment Share on other sites More sharing options...
brian_c._miller Posted November 10, 1998 Share Posted November 10, 1998 I use the Zone system with everything, but I don't use half-stops. <p> Honestly, the Zone system is simply a method to determine what the range of light is in a scene, and knowing if your film will handle it. Will you need to adjust film development? Will you need to pre-expose the film? Yadda yadda yadda, etc. etc., and on and on. <p> The Zone system is most useful with a spot meter. I have a used Pentax meter, and it's great. Buy one, and then if it hasn't been to <a href="http://www.zonevi.com">Zone VI</a>, send it to them. They will calibrate your meter and put a little sticker for the zones on it. <p> Pulling E100S one stop has been great for me. The resulting exposure came out dead on the money. Link to comment Share on other sites More sharing options...
photodr___ Posted November 12, 1998 Share Posted November 12, 1998 Yes, you can use the Zone System to some extent for color film. I assume that you already know that light meters "see" everything as 18 percent grey and that zone V on the 10 step grey scale is 18 percent grey etc. <p> What you need to do is meter the scene you are photographing for highlights, shadows, and your key tone area (the subject of your photograph). Once you have done the metering you decide where the key area needs to be placed on the 10 step grey scale to render it to your liking. You then evaluate where the highlights and shadows will fall after you have placed the key tone. If the highlights are overexposed or the shadows underexposed, you will have to decide if you can live with it or need to alter the placement of your key tone. <p> The Pentax digital spotmeter has an interesting feature that is helpful for doing this. There is a red/orange mark that is used to line up the EV value. On either side of the mark is a scale that goes from 1 (on the left) to 10 (on the right). The scale is marked "TV IRE x10 1:32." It is meant for television use (IRE is Institute of Radio Engineers and is the type of unit measurement used on a television waveform monitor for measuring signal level). But, what it represents is a 5 stop exposure range (1:32) that corresponds nicely to what most transparency films will do. If you put your key tone across from the red/orange arrow, and then note what EV falls on 1 and what EV falls on 10 on this scale you will have a range that will show detail in the shadows (1 marker) and detail in the highlights (10 marker). The really interesting thing about this scale is that it shows compression in the highlights (numbers get closer together as the number gets higher) that just about matches what most transparency films do with highlights. <p> This is about the best you can do. You have to translate colors, shadows, and highlights into shades of grey and then note where they will fall when the key tone is placed. Unfortunately, under/over development of color film does not have the same effect on image compression/expansion as it does with black and white film. So you do not have the total control of exposure and results that can be achieved using the Zone System with black and white film. Link to comment Share on other sites More sharing options...
david_corwin Posted November 13, 1998 Share Posted November 13, 1998 Thanks Bill for starting this thread and the others for contributing. I had wanted to ask the same question, having recently gotten back into experimenting with Velvia, Provia and other reversal films in my P67, after teaching myself the zone system and applying it to TMX with good results. I like the control that it gives me. <p> I would like to grasp an easy to remember system that works for chrome films. To start off, what is the exposure range of transparency film? Does it vary from Fuji to Kodak to Agfa, or with the speed of the film? Is this published somewhere? <p> For Tom it sounds like he gets a range of about 4 stops (zone 3.5 to zone 7.5) Steve sounds like he gets 5 stops. <p> For my purposes, I'm looking for a "rule of thumb" (ROT) approach. So, what zone will hold blacks or shadow areas with detail, and what zone will hold whites with detail? More specifically, what zone will keep detail in puffy white clouds while keeping them white (still talking chrome film here); what zone will keep (some) detail in shadows of buildings or trees or whatever? Keep in mind, looking for a "ROT" approach, as I know there will be variables. <p> Does a polarizing filter in any way affect exposure range on chromes? <p> Brian-when you say you get dead-on exposures from pulling E110S one stop- is the intention to reduce contrast by contraction development? Were you looking to place your whites with detail on zone 7 or 8, for example, because they had fallen on zone 8 or 9, and would have been blown out? <p> Are there charts published anywhere that will indicate what kind of contraction can be achieved with different chrome films by "pulling" a 1/3, 1/2 or full stop? Or is there a "ROT"? <p> I realize I answered a question with many more questions- so thanks to all of you in advance for Link to comment Share on other sites More sharing options...
david_corwin Posted November 13, 1998 Share Posted November 13, 1998 Thanks Bill for starting this thread and the others for contributing. I had wanted to ask the same question, having recently gotten back into experimenting with Velvia, Provia and other reversal films in my P67, after teaching myself the zone system and applying it to TMX with good results. I like the control that it gives me. <p> I would like to grasp an easy to remember system that works for chrome films. To start off, what is the exposure range of transparency film? Does it vary from Fuji to Kodak to Agfa, or with the speed of the film? Is this published somewhere? <p> For Tom it sounds like he gets a range of about 4 stops (zone 3.5 to zone 7.5) Steve sounds like he gets 5 stops. <p> For my purposes, I'm looking for a "rule of thumb" (ROT) approach. So, what zone will hold blacks or shadow areas with detail, and what zone will hold whites with detail? More specifically, what zone will keep detail in puffy white clouds while keeping them white (still talking chrome film here); what zone will keep (some) detail in shadows of buildings or trees or whatever? Keep in mind, looking for a "ROT" approach, as I know there will be variables. <p> Does a polarizing filter in any way affect exposure range on chromes? <p> Brian-when you say you get dead-on exposures from pulling E110S one stop- is the intention to reduce contrast by contraction development? Were you looking to place your whites with detail on zone 7 or 8, for example, because they had fallen on zone 8 or 9, and would have been blown out? <p> Are there charts published anywhere that will indicate what kind of contraction can be achieved with different chrome films by "pulling" a 1/3, 1/2 or full stop? Or is there a "ROT"? <p> I realize I answered a question with many more questions- so thanks to all of you in advance for res Link to comment Share on other sites More sharing options...
twmeyer Posted November 13, 1998 Share Posted November 13, 1998 my experience is that adjusting process times in e-6 developement will change the color of the image. if it's enough to bother you is a personal choice you can determine with a subjective test, if you have three backs, or can shoot sheet film. <p> hit a normal, 1 over, 1 under. then push the under, pull the over and run the normal....normal (!).check them out on a lightbox and decide for yourself. <p> my 4 to 4.5 stop range is for printing unmasked on fuji type 35 or ektachrome radiance. scanning will show a lot more in the shadows, but once you're into clear film, there's not much for even a scanner to see. <p> masking can give you 1 or two more printable stops, but highlights begin to loose their sparkle and the midtones can turn to mush (flat). it takes a real pro "ciba" printer to pull off that type of precise masking. they do exist and are expensive. a good dye transfer will show more detail from shadows and fabulous color, but watch out for your wallet. Link to comment Share on other sites More sharing options...
brian walsh Posted November 14, 1998 Share Posted November 14, 1998 Bill, <p> To supplement the answers already posted, you might want to visit a site titled "The Zone System in Color Transparency Photography" at <p> http://idiom.com/~elight/earthlight/photo_tech_notes/color_zone_p1.html Link to comment Share on other sites More sharing options...
photodr___ Posted November 18, 1998 Share Posted November 18, 1998 For the Rule of Thumb. Zone III will give you detail in the shadows (very dark with detail). Zone IV will be open shadows with lots of detail. Zone VII will give you whites with detail. Zone VIII whites with a hint of detail. Zone IX and above - total white. The information given on the Pentax digital spotmeter dial (1:32) may be somewhat misleading as one reader interpreted that it equates to my shooting for only 5 zones. In one sense it does, in that the film will only give you detail from Zones III to about VII 1/2. You may have a subject with 12 zones of exposure range but you have to make a choice as to how the image will be placed to give you the rendering you want over the 5 zones of available detail. Needless to say, at some point on a high contrast subject you just run out of film response. With a low contrast subject you have much more latitude to place it within the 5 zones of available detail. For example, sand dunes under high thin overcast at 1:00 pm may give you shadows that are only 1 stop less than the sand. With this type of subject I have "overexposed" (placed the key tone - the sand in sunlight) on Zone VI-1/2, which in turn, renders the shadows Zone V-1/2 which is a very "high key" depiction of the subject. Not the least bit realistic but very effective in conveying the mood of place and time. I have used the concept of the Zone system and the ideas of how the Zones relate to detail rendering within the 5 Zones of avialable detail to give me the image I visualized. Link to comment Share on other sites More sharing options...
stevierose Posted December 24, 1998 Share Posted December 24, 1998 I have come to this discussion late, but I believe that I can help. I have found three separate sources that will provide you with the info that you want and have been very helpful to me. 1. "The Confused Photographer's Guide to On-Camera Spot Metering" by Bahman Farzad is a staightforward explanation of using the zone system for slide film. It is straightfoward and very well done. You can get it from Amazon.com.He also has a web site at: http://www.spotmetering.com 2. "How to Shoot Perfect Natural Light Exposures on Color Tranpearency Film" by John Gerlach, is a very lucid monograph on the subject which you can order for a mere $8.00 from Gerlach Nature Photography. Their phone number is: 906-439-5144. It is based upon the workshops he teaches on the same subject and could not be clearer. 3. "The Backpacker's Photography Handbook" by Charles Campbell has a chapter on what he calls the "Chroma-zone System" of slide film exposure which is basically the zone system refined for color tranparency film. He also markets products to help you with this including a set of color cards which are used to estimate tonality. You can get the book through Amazon.com and I have seen it at our local Borders Books. He also has a website at www.photonaturalist.com. All three of these sources explain basically the same concepts in slightly different ways. I hope that this helps. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now