david-m Posted February 18, 2009 Share Posted February 18, 2009 <p>I don't know if I am just being plain stupid here, but I have used my D700 for three months now (and very happy I am too) but today was the first time I used my Elinchrom flash units with it. At shutter speeds of 1/250th there is the 'tell-tale' dark band across the bottom edge that indicates to me that the shutter speed is too fast. At speeds of 1/200th and slower it is fine.<br>I have set the camera to synch at 1/250th, so what is happening here?<br>BTW I used a D2x for three years before the D700 with no such issues. Any clues or suggestions gratefully received.<br>Thanks<br>David </p> Link to comment Share on other sites More sharing options...
ellis_vener_photography Posted February 18, 2009 Share Posted February 18, 2009 <p>How are you triggering your Elinchroms? by wire or wirelessly? If wirelessly , which device?</p> Link to comment Share on other sites More sharing options...
ShunCheung Posted February 18, 2009 Share Posted February 18, 2009 <p>If you are using a flash that is not Nikon i-TTL, you need to be a bit conservative with the maximum flash sync speed: <a href="../nikon-camera-forum/00SK7Z">http://www.photo.net/nikon-camera-forum/00SK7Z</a></p> Link to comment Share on other sites More sharing options...
david-m Posted February 18, 2009 Author Share Posted February 18, 2009 <p>Thanks for these two impressively quick answers.<br> So essentially I should not worry that a) I am being my usual stupid self, that b) the camera does not need to be repaired and c) I should just use 1/200 (which seems to be fine).<br> BTW I first used the Skyports and then switched to a cable, but both gave the same results. <br> Thanks again. <br> David</p> Link to comment Share on other sites More sharing options...
ShunCheung Posted February 18, 2009 Share Posted February 18, 2009 <p>David, it doesn't hurt to double check the 1/250 sec and 1/320 sec top sync speed with a Nikon i-TTL flash. Actually there is already one built into the D700.</p> Link to comment Share on other sites More sharing options...
frank_skomial Posted February 18, 2009 Share Posted February 18, 2009 <p>Just an observation: one of my D200 synchronizes OK even at 1/320 sec, while the other D200 already shows up a little bit of dark edge at 1/320 sec that is usually tolerable and cropped off. Both D200 sync OK at specified max sync of 1/250 with all flashes, and also via Pocket Wizards. </p> Link to comment Share on other sites More sharing options...
ellis_vener_photography Posted February 18, 2009 Share Posted February 18, 2009 <p>I would check it with a nother non Elinchrom flash. as it is possible there may be something in the Elinchrom circuitry that very minutely delays triggering.</p><p>Also what sync mode was the camera in?</p> Link to comment Share on other sites More sharing options...
jose_angel Posted February 18, 2009 Share Posted February 18, 2009 <p>Don`t remember what`s exactly the faster syncro speed of the D700 with my Elinchroms (DX heads), but I can tell you that they don`t work even at very slow speeds with some triggering devices.<br> I like to use 1/125sec with cable and works fine. I don`t have my setup here, I could check it tomorrow if needed.</p> Link to comment Share on other sites More sharing options...
jose_angel Posted February 18, 2009 Share Posted February 18, 2009 <p>Forgot that I have a 600RX at home. I have already checked the max shutter speeds on my D700 and found that I`ll stay with the good old 1/125...I don`t use intermediate speeds, so I prefer to be on the safer side:</p><div></div> Link to comment Share on other sites More sharing options...
jose_angel Posted February 18, 2009 Share Posted February 18, 2009 <p>Now the supposedly max sync speed of 1/320, it still have a little darkening at the bottom:</p><div></div> Link to comment Share on other sites More sharing options...
jose_angel Posted February 18, 2009 Share Posted February 18, 2009 <p>Perhaps the max useable sync speed could be 1/250 with my flash heads, but I`d shoot 1/200 or better below that. If your results are the same, your camera is fine.</p><div></div> Link to comment Share on other sites More sharing options...
david-m Posted February 18, 2009 Author Share Posted February 18, 2009 <p>Thanks again for the replies. Sorry Ellis, but I am not with my camera right now, so don't know what flash mode I set it at, but I will check in the morning (that's UK morning!)<br> Jose, my shots at 1/250 looked like your's at 1/320. Guess I will stay with 1/200 which worked fine.<br> Thanks and regards<br> David</p> Link to comment Share on other sites More sharing options...
rodeo_joe1 Posted February 18, 2009 Share Posted February 18, 2009 I too am puzzled by the workings of the flash synch on the D700. The flash control menu has one setting called "flash synch speed" which goes up to 1/320th sec (for FP enabled flash units), and another setting called "flash shutter speed", which only allows a maximum shutter speed of 1/60th sec. Now the way I use the camera with studio flash is to set the built-in flash to manual at 1/128th power and use this to slave synch with the studio flash units. This works fine, but as soon as I flip the built-in flash up, the shutter speed is automatically set to 1/60th sec, and can't be changed to a higher speed. So I don't think that you're doing anything wrong David. I think it's just Nikon's rubbish (i.e. non-existent) instructions for using the camera with proper studio flash, as opposed to the several pages of instructions devoted to using the camera with Nikon's underpowered and overpriced speedlights. Considering this is supposed to be a professional quality camera, and as such you would expect it to be used with 3rd party external flash units, this is an arrogant attitude for Nikon to take. Incidentally, if you're wondering how to avoid the built in flash from producing unwanted catchlights - simple, I tape a bit of silver reflector material at 45 degrees in front of the camera's flash. This directs the flash upwards and blocks the flash from directly illuminating the subject, while still allowing it to trigger the main units. Link to comment Share on other sites More sharing options...
galileo42 Posted February 18, 2009 Share Posted February 18, 2009 <p>Wild guess: you're using a wireless triggering device which has a max sync speed lower than that of the D700. The Elinchrom does not allow faster than 1/160th. or 1/180th. Neither does the MycroSync. The Pocket Wizard Plus allows 1/250th. If you don't respect these max speeds, you will get the same dark band as when going faster than the camera max sync speed.</p> <p>Worth checking.</p> Link to comment Share on other sites More sharing options...
jose_angel Posted February 19, 2009 Share Posted February 19, 2009 <p>David, even if you don`t see at a first glance the dark band when you`re working at a high sync speed, you could notice that later in the post-processing stage.<br />Check it by yourself: shoot at your desired sync speed to a flat clear surface and then apply some darkening to the image (e.g. via "levels" or increasing "contrast" in a PP application). If there is any subtle darkening you`ll notice that. If not, it`s OK.</p> Link to comment Share on other sites More sharing options...
david-m Posted February 19, 2009 Author Share Posted February 19, 2009 <p>OP here, and thanks for the replies.<br> Just to mention that the flash settings on the D700 were for normal (not rear curtain or whatever) and that I first used the Skyport and then a cable direct from the flash head to the camera. Both methods produced the dark banding at 1/250th but there is nothing at 1/200th. I never had any issues with the D2x and the Elinchroms (which I have used happily for many years), but after reading all your comments I am sure the camera is fine (as in, 'does not need repairing').<br> Thanks<br> David</p> Link to comment Share on other sites More sharing options...
dizeman Posted May 2, 2009 Share Posted May 2, 2009 <p>I am having the same problem, but oddly enough it is not consistant. When I set my D700 on 1/250th of a second, ISO 200 with either the SB800 mounted or wireless, now and then I get the tell-tale speed line rising up from the bottom of the frame. It progresses as I increase the shutter speed as would be expected, but what is unexpected is that sometimes at 1/250th it does not show. The settings are all the same, never changed anything in my test. I just shot five photos and in three of them I had the black edge speed bar and in two the bar was not there. All shot on MANUAL f.8 at 1/250th of a second and yet, there is a variable in the number of times the black bar shows and when it doesn't. WEIRD!<br> What is even stranger is that the black bar in several of the photos does not run the entire length of the bottom of the frame, it runs about half way and then stops and is clear again. That's a new one to me in over 30 years in the biz. Starting to think there is a curtain loose or something. Nope! Camera was bought new and babied, not a bump, grind, scratch, nor dew drop on it.<br> The metering did go funky when I attached the MB-D10 bat grip, but that is for another time.</p> Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now