wood field in the sultry South ?...re: humidity

[john_david_pope]

I am looking to purchase a wood field camera like the Lotus or Wisner.

I live in New Orleans and the camera will have to deal with our extremely high humidity. I want to do environmental portraiture.

The camera will go from air-conditioned car/home to humid swampy outdoors...quite often many times in one day.

Is humidity an insurmountable concern for wood cameras ?

Should I instead go with a metal field like the Canham ?

 

<p>

 

Should I ahve the same concerns with a wooden tripod ?

 

<p>

 

 

john

[cesar_barreto]

John,

Woody cameras may not suffer at all, as wood usually is pretty well

treated and varnished. But you should be quite careful about

condensation on lenses and, even worst, sheet films on holders. Here

in the tropics, those things happen quite often. Good luck.

 

<p>

 

Cesar B.

[chris_patti1]

See http://www.clydebutcher.com/. I'm guessing that if it's not a

problem for this guy, it probably won't be for you.

[bob_moulton]

Bucher uses an 8x10 Wisner, and he takes it into the deepest

humidity. I have used a 4x5 tech.field for about 12 years in wet

climates, some quite humid, with no problem. You might email your

concern to Ron Wisner; he can tell you about his mfg. technique zand

perhaps put your fears to rest.

[dave_willison]

If you can get a copy, take a look at ViewCamera, November/December

1994. This article has a round table discussion featuring Wisner,

Phillips, Canham and Bender. Page 34 has a series of items on how each

manufacturer selects wood and how each deals with the stability issue.

As Wisner notes, there is no way of excluding moisture from wood. Even

a heavy coating of varnish will only reduce moisture by roughly 50%

compared to untreated wood. As a result, wooden viewcamera makers use

a combination of approaches including: (1) selecting old growth woods

and lumber with low shrink ratios, (2) kiln drying, (3) allowing wood

to stabilize over time in controlled conditions, and (4) treating wood

with protective coatings such as Danish oil or epoxy. After the wood

is selected (often by hand), stability is further enhanced by choosing

the right grain and the right type of joint, including finger joints

and dovetails. In addition, many cameras are made by laminating wood

together in layers to increase strength. I hope this allays some of

your concerns.

 

<p>

 

..........................

[lyle_allan]

I've used wooden view cameras for the last three years in the South

Carolina low country. No problems with cameras but you might have to

let the lens come to temperature before you put it on the camera (a

minute or so should do it). As far as a wooden tripod, again no

problem. But if you are using it along the coast and you're getting

into the surf you will have to rinse it down with fresh water and lube

up the moving parts every now and then.

[geoffrey_chen]

John,

 

<p>

 

I have taken a Lotus Rapid field to St. Thomas. No problems at all,

while my Nikon F3 and Sekonic L-508 failed. What I learned: take a

mechanical camera such as Nikon F2 and a non-battery dependent meter

such as Sekonic M398 if you are going to humid places, at least as

backups. Cheers,

[sean_yates]

Nawlins? Humidity certainly didn't bother Clarence John Laughlin

none - he used a Korona. What about Bellocq? I kinda doubt he had

anything to choose from BUT wood.

[andrea_milano]

as far as camera go that can resist anything in terms of humidity the

Walker Titan beats it all, it is made of ABS and stainless steel

cannot beat this conbination, I would be more concerned about the

lenses though but I am sure that a good dose of silca gel can

prevent most damages. Good luck

[richard_deimel]

It's really not a problem.I'm in Miami, Florida, and I have used

nothing but wood field cameras for years, a series of Tachiharas and

now for several years a Wista DX II. All outdoor photography, winter

and summer, in some of the worst possible heat and humidity

conditions. The only problem, as someone has cautioned, might be

condensation on a lens taken from air conditioning and not allowed to

warm up to ambient temperature. If you remember to look at the lens

before your first shot, you'll see it if it's there, and then it's

just a matter of waiting a few minutes. But as to the wood, don't

worry.