rich815 Posted January 9, 2007 Share Posted January 9, 2007 Hello all, <p> Recently got a couple Hassy bodies and unfortunately jammed one. I was putting the 80 Planar on a 500C/M body (both were cocked) and about 3/4 of way thru turning the lens to complete the attachment accidently hit the shutter button at the same time. Sure enough, lens locked on the body. <p> Using online hints from these sites: <p> http://www.ernstweeg.com/tips.htm <p> http://www.photoweb.net/pw_tech/hassy_unjam.html <p> http://www.david-odess.com/faq.html <p> I was able to go in thru the back of the body and use an unjam tool to cock the camera and lens and I did get the lens off. I thought I was home free. but no. <p> Now I'm left with two problems: <p> 1. The body, although showing the white window as cocked and the lens now off, it locked up, the crank cannot move, and the mirror is locked in the up position and will not go down. If I push the shutter button I hear a click and a small metal shaft sticks out the right, rear of the body. I then again go in thru the back of the body, use the unjam tool and it re-sets something and the metal shaft retracts into the body yet still the mirror is up and the crank will not turn at all. And I have tried putting a back on and removing the slide, nothing----mirror stuck up. <p> 2. The lens, after I got it off as described above, was still seemingly not fully set or cocked as I could see right thru the lens glass and the shutter was not closed. After reading hints on the sites above I re-set the slotted "screw" shaft on the back of the lens but it would not take and kept springing back to where it started. I then attempted to touch the small pin within that small half tube on the back of the lens and heard a click and the shutter in the lens closed. Yet the screw slot is still not in line with the red dot and the lens with not mount on my other body, a 500C. <p> So, I'm left with a 500C/M with a stuck up mirror and a lens that I was able to close the shutter yet is seemingly not aligned right to mount on a camera anymore. <p> <b>I've tried all the hints in the links I listed above so please do not say, "go here for your answer: " and show me one of those links. I've tried everything on those sites. My solution is not there.</b> <p> Anyone have any ideas here? Have anything similar happen? Do I need to send it in somehwhere? If so, should I go straight the Hasselblad repair itself (In NJ I believe, if not where?) or is there a repair person that has an impeccable reputation that would be better than Hasselblad itself? (and if so, why?) Anyone in the San Francisco area?<p> Thanks.<br> Link to comment Share on other sites More sharing options...
rich815 Posted January 9, 2007 Author Share Posted January 9, 2007 Oh yeah, I found this site too: http://cesarigd.club.fr/photoe2b.htm No luck. Link to comment Share on other sites More sharing options...
Gary Naka Posted January 9, 2007 Share Posted January 9, 2007 International Camera in Mountain View, 720 Villa St, 650-961-5825. Been a LONG time since I had work done there, but they did a good job for me. Link to comment Share on other sites More sharing options...
vick_ko Posted January 9, 2007 Share Posted January 9, 2007 Send it to David Odess: http://www.david-odess.com/ ...Vick Link to comment Share on other sites More sharing options...
lauren_macintosh Posted January 9, 2007 Share Posted January 9, 2007 Rich here an answer to another lens jams from david Odess: see below David Odess , jan 08, 2007; 12:40 p.m. Ann, If the cocking shaft on the rear of the lens will not turn clockwise without forcing it, try this ... just to the right of the cocking shaft, you will see a pin with a half-moon protective collar around it. Move the pin towards the outside of the lens, and then try to turn the cocking shaft clockwise. If this doesn't work, you'll need to have the lens serviced. If you need a qualified Hasselblad technician, please visit my website. www.david-odess.com Link to comment Share on other sites More sharing options...
jim_mcbride Posted January 10, 2007 Share Posted January 10, 2007 This is why I don't use the damned things anymore (now don't anyone go getting offended here; I'm only talking about myself). I'm admittedly hamhanded and I guess the Hassys have tolerances that are too close for my clumsiness. I have a much easier time handling my Mamiya 645s, but I admit that the pix don't quite reach the quality of the Zeiss glass. My compromise: I try to do critical stuff with a Rolleiflex, whenever I can. I find all Rolleiflex cameras easy to handle, regardless of vintage. I just wish they weren't so expensive. I guess if I wanted inexpensive, I could go buy a Holga. Sigh. Link to comment Share on other sites More sharing options...
ataisa Posted January 11, 2007 Share Posted January 11, 2007 Send the camera to David Odess. It is beyond anything you or anybody else can do for this camera. I am certain that David will not only fix it . He will do a great job, bringing the camera to specs as per de factory and all this is not going to cost you and arm and a leg A Fridman MD Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now