Jump to content

Cold light and inconsistent exposures


andy-

Recommended Posts

I've been looking into the Metrolux and Zone VI compensating timers and would love to hear from anybody who has experience with either one. Since changing to an Aristo cold light I've had a lot of problems with inconsistent print exposures. Even with the heater constantly running some type of compensating timer or voltage stabilizer seems necessary. The Metrolux does seem to have more features than the Zone VI, but I haven't been able to determine if it has any manual control over the light intensity, which I need. The Zone VI ,though, seems easy to use and well received. Price of either is about the same with sensor and footswitch.

 

<p>

 

Instead of controlling the exposure time, is there anything out there that would adjust the intensity of the light instead? Or are there any more economical alternatives to stabilizing the light output? The price tag for the compensating timers is pretty steep and up until now I've been plenty satisfied with my metronome for timing exposures.

Link to comment
Share on other sites

An inexpensive option is to find a used Zone VI Compensating

Metronome timer. I believe these were called Tik-Tock. They connect

to the cold light sensor and vary the beep timing as light output

varies. You will still need to install a sensor and it will not vary

the light output. If you like using a metronome now you might like

one. One bad feature is that the beeps turn on when the light goes

on. So it beeps during focusing and setup. You use a footswitch to

turn on the light and one normally came with the timer. Used should

be under $100.

Link to comment
Share on other sites

I have the Zone VI model, and it's good. I wish I had two channels

that's available on the Metrolux, each with the ability to

separately adjust the growth factor. But, you can't have everything.

 

<p>

 

The only occassional problem that I've had with the Zone VI is that

one can inadvertently touch and change the brightness control, and

thereby change the exposure unknowingly. As a plus, I like the dial

adjustment of time on the Zone VI, versus the push-button control.

 

<p>

 

I purchased an extra sensor and added it to my D2V condensor head for

the incandescent light source. It seems to work fine. There's an

internal housing for the lightsource, and I needed to cut a hole in

this housing to clear a path between the sensor and the lightsource.

 

<p>

 

I have two Zone VI light sources. I'm not sure about how well the

Metrolux will work with Zone VI sensors.

Link to comment
Share on other sites

Andy,

I experienced the same problem and finally broke down and

purchaced the Zone VI compensating timer, as I had the Zone VI

head. I don't regret it, it totally solved the problem and I can see

already that it will pay for itself in saved paper. In an other

darkroom I have used a voltage stabilizer and that also worked,

but perhaps not quite as simply. I believe that was a Zone VI

model as well. The cold light on its own just can not be trusted.

I agree with the other posters to check out e-bay.

Link to comment
Share on other sites

I have the Metrolux II. I bought it mainly because it cost a bit

less than the Zone VI. I use it with the Zone VI head: it has the

proper cable available for the Zone VI sensor. I do not know of a

way dimming the output of the cold light, just the display on the

unit itself. The unit has a couple of other features besides the

extra channel. I has a built in shutter speed tester and an

accessory probe that can be used to determine negative densities on

the baseboard. It has worked very well for me.

Link to comment
Share on other sites

Thanks a lot to all who responded. You've answered my questions and

then some! I really appreciate your input.

 

<p>

 

For the benefit of future cold light buyers, I want to add that I also

talked today with a gentleman from Aristo who was very helpful in

detailing the normal operating 'parameters' of the unit. He seemed

genuinely concerned, not only that the light was functioning properly

but that I wasn't about to spend a large chunk of change on

accessories unless it was necessary. It seems they are definitely a

company that will stand behind their products.

 

<p>

 

Thanks again for your suggestions, they have been very helpful!

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...