bill_glickman Posted February 27, 2000 Share Posted February 27, 2000 Is their any alternative to Scheiders "high end" vacuum backs? When pointing the view camera downwards, the film will buckle in the middle causing focus problems as I have exceeded my Depth of Focus limits. I would guess there must me a way to slide a very hard but thin piece of glass into the film holder which would keep the film from buckling when the holder is parallel to the ground. Has anyone experimented with any systems to prevent film buckling? I have considerd the "high end back", but it requires special film holders and the vacumm part is too big and bulky to carry in the field. Thank you.. Link to comment Share on other sites More sharing options...
simon2 Posted February 27, 2000 Share Posted February 27, 2000 Sinar has its Precision 4x5 Sheet Film Holder and the adhesive models for 5x7 and 8x10. Haven't used any of these; the 4x5 in particular is pretty pricey but simpler than a vacuum back. Check B&H >LF >Sinar >Back Accessories for details. Anybody have any experience with any of these desi Link to comment Share on other sites More sharing options...
bill_glickman Posted February 27, 2000 Author Share Posted February 27, 2000 Simon, thanks for the info.... this leads me to an even simpler method compared to the glass I mentioned above. I imagine some mildly adhesive double sided tape in the film holder would work just the same. Anyone try that before? Link to comment Share on other sites More sharing options...
alec1 Posted February 27, 2000 Share Posted February 27, 2000 Linhof once made vacuum backs for use in the field. They had a little tube you sucked on to produce the vacuum at the right time. Haven't seen one for a long time, but I'm sure they are out there somewhere. You might try contacting some camera stores in Germany where I'm sure they were more plentiful. Link to comment Share on other sites More sharing options...
bob_salomon3 Posted February 27, 2000 Share Posted February 27, 2000 "Linhof once made vacuum backs for use in the field. They had a little tube you sucked on to produce the vacuum at the right time. Haven't seen one for a long time, but I'm sure they are out there somewhere. You might try contacting some camera stores in Germany where I'm sure they were more plentiful. " <p> They didn't work. <p> Hoffman makes vacuum film holders though that do work. Link to comment Share on other sites More sharing options...
david_munson Posted February 28, 2000 Share Posted February 28, 2000 Linhof also made "regular" 4x5 film holders that used a spring loaded panel behind the film to hold it flat. I've got one and it works quite well. My only complaint is that loading the film is a bit of a task, and I needed to slightly modify one of the film removal levers (each side has a little lever that pushed the film out of the end of the holder when you're unloading it), but these are only minor complaints. Otherwise, I have been very happy with it's performance. They aren't terribly hard to find used and only run about $30-$45 each. <p> -Dave Munson <p> -Dave Munson Link to comment Share on other sites More sharing options...
pat_raymore Posted February 28, 2000 Share Posted February 28, 2000 Bob, Tell us more about the Hoffman vac holders. Where can they be obtained? Link to comment Share on other sites More sharing options...
bob_salomon3 Posted February 29, 2000 Share Posted February 29, 2000 "Linhof also made "regular" 4x5 film holders that used a spring loaded panel behind the film to hold it flat. I've got one and it works quite well. My only complaint is that loading the film is a bit of a task, and I needed to slightly modify one of the film removal levers (each side has a little lever that pushed the film out of the end of > <p> Not quite. These were plate and sheet film holders and the spring loaded plate was not a pressure plate for film. It was a means of making the holder compensate for the difference in thickness between film and glass plates. the lever was to easily remove glass plates without scratching the plate. <p> A spring loaded plate in a sheet film holder can't really hold film flat as it has nothing to push the film against. <p> As for Hoffman holders you would have to contact the manufacturer who is somewhere in NY. Link to comment Share on other sites More sharing options...
bill_glickman Posted February 29, 2000 Author Share Posted February 29, 2000 Pat, I am trying to locate Hoffman also.... I have seen them advertise in View Camera Magazine a few times, but can not find that issue... if anyone has a phone # or a link, please pass it along...Thanks for the lead Bob... Link to comment Share on other sites More sharing options...
sean_yates Posted February 29, 2000 Share Posted February 29, 2000 In general a search of the archived questions can yield previously posted info but to save you the time here it is: <p> Hoffman Camera Corporation 19 Grand Avenue Farmingdale, NY 11735 1-516-694-4470 Link to comment Share on other sites More sharing options...
stephen_willard Posted February 29, 2000 Share Posted February 29, 2000 Bill, the double side tape appeals to me. Simple, inexpensive, and light weight. I used to use the tape to hold down my paper on the easel unitl I go a vacuum easel. It worked great. Link to comment Share on other sites More sharing options...
david_munson Posted February 29, 2000 Share Posted February 29, 2000 Oh my, I gues I was a little misinformed about the linhof holders. Thanks for providing some more accurate info. I still think, though, that they do hold the film flatter than most other regular holders, but maybe that's just a matter of overall quality. <p> -Dave Munson Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now